Press "Enter" to skip to content

nuxx.net Posts

New Bike: 2013 Salsa El Mariachi Ti

Today I finished assembling my new bike, a complete 2013 Salsa El Mariachi Ti, size medium, that I purchased from Trail’s Edge. For quite some time I’ve wandered a dedicated, geared hard tail 29er, and so back in September 2012 I ordered this one. It was originally slated to ship in mid-December 2012, but (apparently due to Salsa’s growing popularity) it slipped until this past week (April 2013). Regardless, I’m happy to have it.

This was purchased as a complete bike and received it in the box so I could put it together myself. This worked out well because I both like assembling my own bicycles, and it allowed me to swap out the parts I was immediately wanting to change, like the saddle, handle bars, grips, and tires. I end up spending around 12 hours on the initial assembly of a bike this way, but then I’m comfortable with how it went together and how it’d been tuned, and when something goes awry I’m ready to take care of it.

The only problem I had during this assembly was with the tubeless setup on the rear wheel. I’d originally intended to use a Specialized Fast Trak Control tire, but I had enough difficulty getting it installed that I headed over to Rochester Bike Shop mid-assembly and picked up a Kenda Small Block Eight and used it instead. During the install I found the Specialized Fast Track on the Stan’s NoTubes ZTR Arch EX rim was such a tight fit that it was very difficult to get the tire fitted, and then it wouldn’t seat. Using my High Volume Inflater I attempted to overinflate the tire to get it to set, but before it did that the other side blew off the rim with an incredible bang, with enough force to bend and crimp the tubeless valve inside the head of the inflater. Thankfully the rim wasn’t damaged, so after getting the new valve and tire everything went together just fine.

I’m happy with how the bike came out thus far, with two exceptions, one minor and one major. The minor exception is that I don’t like the red logo on the side of the stem. It’s not terrible looking as there is some red at the bottom of the fork, but the bike now needs something red on the rear end to balance the color. This may get replaced, though, as the major problem is one of reach. While I’ve got the seat/crank area setup properly, the Salsa Bend 2 bar is not a drop-in replacement for the Ragley Carnegie’s Bar that I prefer.

The Bend 2 is both a little wider and doesn’t sweep back as far as the Carnegie’s Bar, and when measuring from the nose of the saddle to the bolts in the grip (same saddle and grips on both bikes) the El Mariachi Ti has 45mm more reach (saddle to grip) than either my steel El Mariachi or Titus Racer X 29er. It’s only a smidge longer than on the Mukluk 2, so I will give it a go for this weekend (scheduled for 8.5 hours of riding total) and see how it feels. I’ve thought that I’m perhaps a bit too upright on either the Titus or steel El Mariachi, but they’ve also felt fine for many, many hours of riding. Since the Carnegie’s Bar is no longer made and nearly impossible to find for sale I may have to investigate a stem change and trimming the bars if the current setup doesn’t work out. At least that should take care of the red color imbalance.

As with many tubeless setups the tire loses air for a while until a few rides can get the sealant wholly distributed, and this caused me one problem. When I got home from work today I found that the rear tire had lost its air, causing the bike to fall over in the stand. In doing so the top tube brushed a table leg, putting a small scuff in the finish. This is probably nothing compared to damage which the bike will incur from kicked up sticks and rocks, but it’s a bit frustrating for that to have happened before I even got it on a trail.

Finishing off the bike I topped the Niner YAWYD with a cap from Southern Tier Brewing Company. This black bottle cap with a shovel and traditional wood mashing paddle fits very nicely on the bike, and is a (admittedly non-Michigan) brand that I really enjoy. I’ve taken the bike for a ride around local neighborhoods to bed in the brakes and get the Garmin Edge 500 to auto-calculate a rear wheel size, so it’s ready to ride this weekend. This proved that the Elegant Cadence Magnet that I’d posted about earlier works great, even using a lower profile magnet than the one pictured before. It’s much nicer than a magnet sticking off the back side of the pedal, secured with adhesive and a cable tie.

So far I’m really happy with this bike, and I expect this to continue as I ride it more. There’s a little bit of fit tweaking like with any new bike, but I think I’ve got it pretty close, and hopefully it’ll work well for the foreseeable feature, allowing me to successfully complete a number of long rides. Weighing in at 26.16 pounds (as pictured here, including the Garmin) it’s also one of the lightest bikes I’ve ever owned.

I’ve got a few parts leftover that I probably won’t use (Salsa Back Country Lock-On Grips, WTB Pure V saddle, too-short Salsa Pro Moto 1 Seatpost, Salsa Pro Moto 1 Carbon Flat handlebar, Continental Trail King 2.2 tires) on this bike, but they’ll be good things to add to the spares pile. I’ve also got a SRAM X7 S1400 2×10 crankset without bottom bracket (it was stock on the El Mariachi Ti, I replaced it with the X0 that I picked up a few months back), but as it is 104 BCD I can see myself using it on another bike as a single speed or 1×9 crankset.

A bunch of photos of the bike, including stock photos and some of the parts added to the base build can be found in this album: Salsa El Mariachi Ti. Photos of the complete bike can be found here.

Here’s the exact components on it, as of this evening:

Frame: 2013 Salsa El Mariachi Ti (Medium / 17″)

Fork: Fox Racing Shox OE, CTD w/ Open Bath Damper

Headset: Cane Creek 40 ZS44/EC44

Bottom Bracket: Truvativ GXP (XR / Black)

Crankset: Truvativ 2011 2×10 X0 GXP (00.6115.422.070, Blue)

Rims: Stan’s NoTubes ZTR Arch EX 29er (Blue Accents)

Tires: Front: Schwalbe Racing Ralph HS 425 (29″ x 2.25″, New Style, TL-Ready), Rear: Kenda Small Block Eight (29″ x 2.1″, DTC, non-SCT, K1047)

Hubs: Front: Shimano HB-M788, Rear: Shimano FH-M785

Spokes: DT Swiss Competition (Black)

Handlebar: Salsa Bend 2 (23°)

Stem: Salsa Pro Moto 1 (100mm)

Seatpost: Thomson Elite (Straight, 27.2mm x 410mm)

Seatpost Collar: Salsa Lip-Lock (32.0mm)

Saddle: Specialized Phenom Comp (143mm, Grey / Black Underside)

Grips: Ergon GP1 BioKork (Large)

Shifters: SRAM X9 2×10 Trigger

Front Derailleur: SRAM X7 High Direct Mount

Rear Derailleur: SRAM X0 Medium Cage (Blue)

Cassette: SRAM PG 1070 (11-36)

Chain: SRAM PC 1051

Pedals: Crank Brothers Eggbeater 3 (Blue)

Brakes: Shimano XT, Levers: BL-M785, Calipers: BR-M785, Front Rotor: SM-RT67-M (180mm), Rear Rotor: SM-RT67 (160mm)

Bottle Cages: King Cage Iris

Other Accessories: Mirracycle Original Incredibell, Niner YAWYD Top Cap, Planet Bike Superflash Stealth, Scotch 2228 (Chainstay Wrap), Race Face Crank Boots, UHMW Tape for Cable Rub and Heel Rub, Garmin GPS Mount.

Leave a Comment

Adobe Creative Suite Weirdness on OS X after Manual Backup

I’d been having a problem on my main OS X machine where, every time Adobe Acrobat would try to do a security update I’d receive a cryptic error message stating that I’d modified the installation and therefore the update wouldn’t work. During use of Creative Suite products (mostly Illustrator) I’d occasional see odd quirks, like slow(-er than expected) application launching or updates that seemed to run more than once.

After some digging I eventually found that the root of the problem was a backup of my Applications folder that I’d created when I reinstalled the OS post-SSD failure.

In recovering from this failure I figured that a clean OS install would be nice, so I moved /Applications off to a corner of my disk (/Volumes/Cruft/Storage/Applications.old if I recall correctly) and let it sit, just in case I forgot to copy or reinstall something and was later wanting for it. It appears that these .app bundles (the special folders suffixed .app, such as Adobe Illustrator.app) were still being seen as valid programs, and sometimes run instead of the intended ones in the root of the drive. This resulted in updates working strangely, slow launching as they weren’t read from the SSD, and the other quirkyness that I’d seen.

Having been a number of months since I created the …/Applications.old backup and not needing anything in there I deleted it, and all was better. Adobe Acrobat updated once more, and since then everything has worked as expected.

So, if you’re having problems with Adobe application updates failing weirdly on OS X, look around for other copies of the application bundles. Maybe this is your problem as well…

Leave a Comment

IKEA FIXA Metric + Standard Tape Measure

IKEA, purveyors of useful (and usually) imported items has one item that I think will be of particular use to those interested in the mechanical side of cycling: FIXA Tape Measure (item 402.375.57), a metric and standard tape measure which retails for $1.29 in US stores.

Bicycle measurements, especially frame dimensions, seem to be randomly specified in metric or standard units. To accommodate this and support measuring tire circumferences I bought a Stanley metric tape measure via eBay from Canada, but I thought it’ll be really nice to have this dual-unit one. Now I do, and it’s cheap enough that I don’t mind throwing it in a tool bag with other items, leaving it there to get scratched and nicked up, nor loaning it to someone and potentially losing it.

1 Comment

Pub Pedals

To make non-bike-shoe riding easier I picked up a pair of Windwood Decksters a couple of years ago, but I never really used them because my primary use for flat shoes on clipless pedals was doing trail work and the Decksters were prone to popping off when twisting one’s foot, like when riding on trails. Instead when taking my bike out for trail work I’d just deal with riding in boots on Eggbeaters or wear bike shoes.

With a recent successfully-funded Kickstarter campaign Pub Pedals — a slip-on platform for Crank Brothers Eggbeaters — came to be. Nick had purchased a pair from the original campaign and after they arrived I saw how high quality they were and that they’d meet a need of mine, so I ordered a pair. Today they arrived, and after some basic testing I’m quite happy with them. I still have to actually try them out for basic riding on trails, but I expect them to work quite well.

I first tried them on some older Eggbeater SL pedals that are on my Mukluk 2 and they installed pretty easily, but weren’t loose enough to come off easily. I then tried them on the newer Eggbeater 3s that are on most of my bikes and they were sufficiently difficult to install that I sent a note to Nick asking if his fit. They did, so I tried mine again and was able to cajole them in place by wearing gloves and spreading the cages a bit with my hands. Eventually they fit in place, snugly enough that I see almost no chance of them coming off during even fairly aggressive trail riding. (I’d probably slip off the pedals before I could apply enough force that they’d push off of the pedals.)

Come next time I’m out doing trail work, provided there’s no need to carry long tools, I strongly suspect I’ll be giving these a go. Or, maybe I’ll slip them on next time I’m looking at taking a ride up to Sherwood for some dinner and beer… After all, they are Pub Pedals.

1 Comment

Evaporated Tungsten Deposits

A few days ago when I entered the garage I heard a noticeable 60 Hz buzz. Since this part of the house contains only fluorescent lighting I was a little confused at what it could be. The noise seemed to be coming from one of the incandescent bulbs on the ceiling; one which was giving off a strangely dim and off-color light. Switching the lights off then back on finished off the failing bulb, and it burned out in a typical flash.

I’m not completely sure what was occurring, but with quite a bit of darkening (likely condensed metal vapor) on the inside of the bulb and the odd colored light I strongly suspect that a gap had formed in the filament but was arcing, then on next power cycle the filament blew itself apart.

This bulb is one of two 300W incandescents that I use to illuminate the garage. I’ve considered putting in some bright, all-temperature fluorescent lighting, but doing that would be considerably more expensive than occasionally installing ceramic sockets and spending $5 every couple of years on a bulb.

2 Comments

Bent Surly Chainring

About a year ago I purchased a spare Surly 34t chainring from someone on the MMBA Forum, just like the one I’d originally fitted to the El Mariachi after building it up as a single speed. I somewhat regretted the purchase, but figured that one day I’d find a use for it.

Today was that day.

While riding from Great Baraboo out to Metro Beach (Lake Erie Metropark), just after crossing Gratiot I pedaled and noticed that my bike was producing an odd skip. At first I thought that perhaps the jockey wheels on the derailleur were binding and causing the chain not to thread through, but eventually I noticed that the chainring was a bit bent. I dealt with the skipping and finished up the ride, then investigation at home showed that the chainring was bent a bit towards the bash guard, causing the chain to not settle on the ring at part of the pedal stroke, leading to the skipping feeling as it finally dropped in place.

Thankfully I had the spare chainring so I was able to swap that one on and have the bike ready for riding tomorrow.

This past Saturday while out on a longer ride to Richmond and back one of my chainring bolts came a bit loose and was occasionally brushing the N-Gear Jump Stop that I use to keep the chain on the bike when used as a 1×9. I tightened it up last night and confirmed that the chainring was straight (read: it hadn’t bent while one bolt was loose) and figured everything to be good. I can’t help but suspect the two are related, but as the ring wasn’t bent last night and bolts were still tight when I removed the ring today, I’m not sure how this happened. It’s also bent between the bolt holes, which implies that the bolts were snug when it happened.

My friend Roger reported bending a Surly ring on a bike with tight bolts, so maybe it’s possible for them to get loaded in just the right way for it to be a problem. I’m considering getting a Roger-recommended On-One Stainless Chainring as they look to be much more robust than the Surly rings, but for now I’ll just stick with the replacement Surly. The Salsa Ring Dinger bash guard that I’m using as an outer chain guide is also a bit beat up and slightly bent (outward) so when I get the On-One ring I’ll probably replace that with a nice BBG Bashguard.

At least things are back to working again.

Leave a Comment

Heart Rate Testing Confuses Me

I’m following the LW Coaching 100 Mile Mountain Bike Race – Finisher Plan again this year, again in hopes that it’ll get me ready to complete the Lumberjack 100 race in June. Part of this involves testing my Lactate Threshold Heart Rate, or basically, my average heart rate over 20 minutes of riding my bike as hard as I can. This average is then run through a formula (one of many — I’m using this one from LW Coaching) to determine heart rate zones. When working out (really, just riding my bike) I then try to stay in the prescribed zone for the listed amount of time, with the idea that this helps build endurance at that zone.

For example, the zones that were calculated for me off of today’s test with an average heart rate (HR) of 170 BPM during the test are as follows:

Zone 1 – Recovery: 111 – 137 BPM
Zone 2 – Aerobic: 138 – 152 BPM
Zone 3 – Tempo: 153 – 159 BPM
Zone 4 – Sub Threshold: 160 – 169 BPM
Zone 5 – Super Threshold: 170 – 180 BPM

Much of the planned riding in preparation for finishing a 100 mile race involves hours of riding in zones 2 or 3, which seems easy at first, but gets difficult as the hours progress. It does seem to work, though, as it helped me get up to riding 8+ hours comfortably, as long as I was capable of pacing myself. Hopefully this’ll continue to help this year, and I won’t quit early like I did last year. I’d really like to finish this race at least once.

Last year I first performed this test on the trainer on the second day of the plan, but ended up with a low-seeming heart rate of 153 BPM. I tried again on April 4th, 2012 and got a result of 166 BPM†, which is what I’ve used for my HR zones for training last year. This current result of 170 BPM has pushed the zones up a bit from last year, and I hope this helps push me a bit more.

Despite using the same route as last year for the test and following a similar warmup I can’t help but question the variances in numbers. Today was much colder than last year (42.3°F vs. 59.7°F), the bike used had slightly knobbier tires and a suspension fork, and there was a lot more wind today. Maybe the harder conditions and higher average HR mean I’ve become a capable of a little bit more over the last year? I’m not really sure.

The more I read about HR zones and LTHR calculation the more confused I become. I was pushing myself as hard as I felt I could go without failing, so with Joe Friel‘s (a pretty well regarded coach) simple adage…

Do not be concerned with anything other than are you going as hard as you can go right now. If the answer is “yes” then you are doing the test right.

…maybe I am doing it right.

† This was then recalculated on May 8th, 2012, but likely due to a loose HRM strap I ended up with a maximum of 225 BPM and an average of 187 BPM, clearly erroneous numbers. As a result I just stuck with the previous number of 166 BPM from April.

Update on May 8, 2013: Yesterday, as prescribed, I performed another LTHR test. Riding the same route (but with a different warmup) in 35°F warmer weather (79°F vs 34°F) my average HR was 2 BPM faster and average speed was 1.5 MPH faster. I think it may have been a bit less windy, which likely explains the higher average speed.

This pushes each of the zones up slightly to the following, which is what I’ll likely use for the remainder of the training plan:

Zone 1 – Recovery: 112 – 138 BPM
Zone 2 – Aerobic: 139 – 154 BPM
Zone 3 – Tempo: 155 – 161 BPM
Zone 4 – Sub Threshold: 162 – 171 BPM
Zone 5 – Super Threshold: 172 – 182 BPM

Leave a Comment

Barry-Roubaix: The Clothing

Rob’s post on Barry-Roubaix which included a description of the clothing worn made me want to note the same thing. Not for any reason of style, but because I find dressing for longer cold weather rides to be a bit confusing for some (they sure were for me!), so I hope these notes can help others in a similar situation. (It’s also an excuse to post this photo of Roger, Nick, and I just after starting the race.)

Saturday’s weather in Hastings was right around freezing. My bike computer recorded an average temperature of 32.5°F during the race, and the temperature when I last checked the weather before leaving for the start was 28°F. There wasn’t much wind, but being a road race I had to be ready for 10-20 MPH headwinds throughout the day, plus more while riding down some hills.

Here’s what I wore, which is fairly typical for me in these conditions:

  • Pearl Izumi Barrier GTX Shoes
  • Generic Kirkland (Costco) Tall Wool Socks
  • Voler Thermal Bib Knickers (Trail’s Edge logo from team order)
  • Under Armor Thermal Base Layer (usually a generic Costco one, but this was a gift and is more form fitting)
  • Voler Short Sleeve Jersey (Club-Cut, Full Zip, Big Ring Coffee from team order)
  • Voler Wind Jacket (Trail’s Edge, also from team order)
  • Descente Coldout Beanie
  • Giro Xar Helmet
  • Pearl Izumi Gavia Gloves

For other rides around this temperature or colder I’ll often use Trail’s Edge Moose Mitts with springtime-weight gloves. I really like these for keeping my hands warm and bike controls accessible, but on warmer days like this when I’ll be trying to push myself (such as a race) they can get too warm. Thus, just as during Iceman, I opted for simple gloves. Regardless of what I chose for keeping my hands warm they always seem to get painfully cold within the first 5 or 10 miles, then suddenly warm up and be fine for the rest of the ride. I guess that must when I warm up and my internal thermostat decides that there’s sufficient heat that some can be spent on warming extremities.

I’ll also tend to refrain from shaving my head or face for 4 or 5 days before an event like this. The bit of scruffy facial hair does a great job of keeping the cold away.

Leave a Comment

2013 Barry-Roubaix on a Fatbike

Today was the 2013 Barry-Roubaix dirt road race, and I participated riding my 2012 Salsa Mukluk 2 fatbike. I ended up with an official time of 2:39:09 and 14.2 MPH average, placing 33rd of 58 in the 36 Mile Fatbike category (results here). I would have liked to have finished in a quicker time than I did last year (2:21:42 / 15.2 MPH average), but as this year’s course was a mix of frozen dirt roads and ice with some rutted mud and I was on a heavier and slower rolling bike, I’m happy. There were many hills that I would have normally pedaled down, but this year’s ice found me (and many other folks) gingerly coasting down them, not braking or changing course. Had conditions been like they were last year times probably would have been faster across the board.

Earlier forecasts looked like the roads would be greasy, peanut-buttery mud, so I set out ready to stop and fix my bike a number of times, but this wasn’t needed. Even with the ice I didn’t fall or step off my bike once, and my bike was almost as clean at the finish as it was at the start. From what I could see my dripping nose added more filth to the bike than the course did.

Differing from previous years the race started and finished in the beautiful town of Hastings, Michigan. In the past it had started at Yankee Springs with the easternmost point near Hastings, but this time the western-most point was near the old start. This worked wonderfully, as the entire town was set up for the race with businesses open early and staffed up for the almost-3000 participants and family members, with the start and finish lines right downtown. Most intersections had police directing traffic, there was a blocked-off street post-race party area, and it all felt like a whole-town event. This venue change was an excellent move.

On the suggestion of our friends Nick and Marty we booked a room at the Parkview Motel, which was a great choice. Not only were a bunch of other friends and acquaintances staying there as well, but it was four blocks from the start/finish area. All I had to do for the start of the race was dress, put my stuff in the car, to check out, and ride to the start. It wasn’t even far enough to be considered the remotest of a warmup! After I left the room at about 10am Danielle continued to sleep, then being in a downtown-ish area she wandered into some shops then sat in a coffee shop until it was time for me to finish. This all worked out very well, and I hope to stay here again. While the place was a bit old, it seemed reasonably well cared for and everything was very clean. At ~$66 total for the night’s stay it was a great choice.

There was one scary part to today’s ride, but thankfully I didn’t see much of it. At the top of one of the most sustained climbs in the course a rider apparently fell off his bike and wasn’t breathing. An acquaintance of mine was one of the folks giving him chest compressions (for a total of 18 minutes) right in the road before the EMTs arrived and got to work on the guy. From what I’d heard and read a few places online he had a pulse when he left in the ambulance, was airlifted away, and is still in the hospital. I really hope he’s all right. (More info starting here in the MMBA Forum.)

This sort of event is scary, but one could have a heart attack doing stuff around the house or just sitting and watching TV. So long as one doesn’t overdo it, the benefits to strenuous exercise (particularly if it is fun) likely outweighs the potential risks.

The Strava page showing my statistics from today’s race can be found here. Official results from the 36 mile race can be found here.

(That photo above is Roger Class’ Pugsley, Rob Tranter’s 2012 Mukluk 3 (which he’d purchased from Nick Shue), and my 2012 Mukluk 2 with different tires and chainrings from stock, all propped against a wall outside of the motel rooms. The three of us, along with Nick and Marty, and Rob Ritzenhein all entered the fatbike class. Erik and Kristi rode their normal 29ers.)

Leave a Comment

Mukluk Lights: Removed

This evening I removed the front and rear lights from the Mukluk 2 and washed it in preparation for Barry-Roubaix. With the longer-than-hoped-for winter and the predictions of snowy and icy roads during the race I figured it’d be best to bring a bike with big, fat tires. I think it’ll be fun, too.

Built up at the very end of 2011 this light has worked out extremely well for night time and winter riding. I won’t need it during the race, the days are rapidly getting longer, and after the race I’m anticipating most of my riding happening on a different bike, so I don’t think it’ll be needed much more for now.

Leave a Comment