Press "Enter" to skip to content

Category: beer

Gas Distribution Manifold and Dessicant

Published March 6, 2011

This afternoon I added a bit of a luxury to the Kegged Beer Cooler, a three-way gas manifold. While not necessary, this will allow me to easily shut off gas to different connectors if I’m needing to play with different pressures for force carbonating beer, soda, fruit, etc.

Since I was drilling from the inside of the cabinet outward without using a guide the external screw heads aren’t quite lined up (picture). This is disappointing because it doesn’t look as nice as it could, but I guess I’ll just have to leave it. To be sure that I didn’t hit any gas lines I first cut small holes in the aluminum liner with a pointed razor blade, tore back the metal with needle nose pliers, then poked carefully through the foam with a plastic tool until I reached the steel outer wall. The foam was then cleared out using a drill bit in my fingers, and then I completed drilling through the outside.

A few days ago I received some desiccant bags purchased from eBay (picture) and those are now in place as well, so the kegged beer cooler project is pretty much finished. I may eventually add external taps, but for now using picnic-style taps inside of the unit should suffice.

Leave a Comment

Inconvenienced by Safety

Published March 5, 2011

A few weeks back I ordered this turkey fryer setup from Cabela’s to replace the burner/regulator that I had problems with a few weeks back. Today when setting it up for use I found that there is an electronic interlock on the gas line which will cut off the gas flow after the last time it was manually reset.

I attempted to remove this, but as can be seen here there is a laquer-like thread locker on the fitting between the regulator and the interlock. While this likely won’t be a huge issue, I’d really prefer to simply concentrate on brewing beer and not pressing a button to keep things running.

UPDATE: In practice this wasn’t that much of a hinderance. The large red button which starts the gas flowing and resets the electronic timer serves as a quick turn-on, and the black button is a good emergency-off in case of a boil-over. A green light illuminates when the gas is flowing and it starts blinking before the gas shuts off, giving one ample time to press the red button and keep gas flowing. While it would be nice to not have this safety in place, it’s not as difficult to deal with as I’d expected.

2 Comments

Kegged Beer Cooler: Complete

Published March 3, 2011

The kegged beer cooler is complete, sitting in the basement, and is actively cooling what remains of two kegs of beer. Tonight I ran the gas lines, fitted everything into place, and set it up against one wall of the basement. It’s currently set to start cooling at 40°F and shut off at 35°F ambient temperature in the unit, which I expect to keep the beer at somewhere in that range. It may be necessary to narrow the band to something a bit narrower, but I’ll be able to determine that after putting a full keg of beer in the freezer and monitoring it.

I’ve been considering fitting the fridge with taps, but for the time being I think I’ll just stay with using picnic-style taps inside the unit. Actual beer faucets are around $100/each after considering all mounting hardware, and I don’t think they’ll provide enough benefit to justify doubling the cost of the unit.

Here’s some more notable photos of the unit throughout its progress:

· Completed chest freezer to beer keg conversion.
· Looking inside at two corney kegs, party tap-style dispensing lines, gas lines, temperature sensor, etc.
· Gas line transition from the compressor compartment into the body of the freezer. It is held in place with twist-type reusable cable ties.
· Temperature probe in place and gas line and Y fitted. Excess foam was left in place to serve as a hose guide.
· Operational Johnson Controls A419 temperature control indicating that it is currently cooling.

All of the photos can be found here. And yes, Roxie approves of it.

3 Comments

Temperature Control Fitted

Published March 3, 2011

The temperature control for the kegged beer cooler fitted and it seems to work. It started, cooled the unit until the appropriate temperature was reached, then turned itself off. Now I just have to run the gas lines and see how it goes with actually cooling beer. This will require a little bit more hardware, although I’ll probably only fit it out for two kegs for the time being, as that’s how many I have. It’s too bad that my current kegs are also almost empty, as I won’t be able to run it fully loaded. I guess it’ll be time to brew more soon.

I also need to consider monitoring temperature in the unit or attaching the probe to a specific keg. I think that in the unit will be sufficient, but for the first couple weeks I’ll double-check this by occasionally checking the temperature of a keg itself.

New photos from tonight’s work are can be found on this page.

(Yes, I know those screws are too long, but they are what I had laying available. Oh well, they neither interfere with anything nor will they be seen once the unit is closed up.)

1 Comment

Kegged Beer Cooler Ingress Fittings

Published March 1, 2011

Meijer is great for when it’s 10pm and the next step of your project requires Great Stuff spray foam insulation.

Continuing the project to turn a chest freezer into a temperature controlled cooler for home-brewed beer (previously) I made a hole inside the cabinet (picture) the size of a film canister without hitting any of the gas lines. This was done by marking a hole, then carefully tearing away the aluminum liner with pliers, then digging through the foam with a screwdriver before finishing off the hole with a drill and file. Looking around the basement I came across some plastic pieces that were perfect for the gas and temperature probe ingress fittings, fashioned out of a 10cc syringe and a used bathroom water supply line that I’d once had (incorrectly) fitted to my to my toilet (picture).

These fit very nicely into the hole. With the flange on the syringe and the water line nicely fitting up against the inside of the freezer’s compressor compartment both plastic bits nicely stayed in place nicely (picture) making surrounding them with spray foam insulation (picture) very easy. I fitted a scrap piece of vinyl tubing in the syringe housing to keep foam out, and it did a great job. Once removed (picture) there is now a clear ingress for gas, and the temperature probe should sit nicely on top of the grey plastic tube holding it nicely mid-level in the unit without touching any sidewalls.

Now all I have to do is fashion a mount for the temperature controller, wire it in, fit the temperature probe, run gas lines, and build a CO2 tank retention system. This is probably only a couple more evenings worth of work, which should be right in time for the wit that I’ve currently got aging and which is due to be kegged on Monday. Oh, and I might cover the lid with some horrible contact paper design, perhaps even something as bad as butcher block.

(Yes, this does mean that all beer served from this cooling unit will be heavily dependent on both an old (but unused) syringe and something which once supplied water to one of my toilets.)

Leave a Comment

Sour Short’s The Magician?

Published February 21, 2011

The eloquent, swift and skillful master who makes things happen.

Despite the lack of serial comma Short’s Brewing Company’s The Magician is a tasty beer. However, I think I may have an off pack that is tasty but in the wrong way; something nice caused by the beer going bad. Short’s describes the beer is described as…

A lustrous dark red London ale with a rich malt combination that lends complex notes of toasted caramel, raisins, chocolate, and roasted toffee. Very light hop additions let the true malt characters promenade throughout the duration of this pleasurable experience.

…yet what I have here in my glass is quite sour, almost like Rodenbach. It’s not bad, but it definitely doesn’t taste like the description reads.

I think I’ll drop Short’s a note and ask them if I have a bad pack.

Leave a Comment

Short’s Black Licorice Lager

Published February 18, 2011

Breweries like Short’s Brewing Company are the reason why I feel that the US has the best overall beer in the world. While there are countless breweries world wide that make excellent beer, there seems to be a strong interest in this country on eschewing the standard beer styles and experimenting with the different ways that a fermented beverage can be made to taste good.

This beer here, Short’s Black Licorice Lager is a perfect example of this. While this would likely fall into the catchall Specialty Beer style, it cannot be discounted as just another odd beer. While the description of how it is a dark lager aged on anise seed, vanilla beans, and chocolate mint lime leaves may be a bit off putting at first, it makes for an extremely good, pleasant beer.

Leave a Comment

Y Fitting

Published February 14, 2011

Thanks to this shiny piece of metal, some more thick wall gas tubing, and another ball lock connector I now have the ability to dispense beer from (or carbonate) two kegs at once. Not only is this more convenient, this will be important when it comes to wedding stuff as the place where we are having our reception requires us to bring our own beer and thus our own dispensing equipment.

Now I just need to acquire a small chest freezer and some temperature control equipment to have a constant 40°F facility for storing such things. The garage worked great in the winter, but as it’s warming up I’ll be needing somewhere else soon.

2 Comments

Area 51 is Drinkable!

Published February 10, 2011

It might possible be a bit cloudy, but the Area 51 American IPA (previously), which is really more of an American Pale Ale, is ready to drink. Comparing it to other beer photos of mine I think it’s pretty spot-on style-wise, and taste-wise it’s really quite nice. This is the first beer that I’ve made which I’d easily think came from a proper brewery had I not known that I made it.

This, plus the ease of kegs, is a good thing. If I can keep up quality like this I’ll be quite happy and likely brewing a lot of my own beer in the future.

Leave a Comment

Blue Cheese and Bacon, etc

Published February 9, 2011

Here is a blue cheese dressing and bacon salad made with a wedge of iceberg lettuce. Danielle made this for dinner on Monday evening and it was absolutely wonderful. I had more of it for lunch the next day, and it really hit the spot then too.

Here’s some other moblog photos that I’ve taken recently:

· Looking out from an elevator at the RenCen at an artificially accelerated sunset.
· My reflection in an elevator while heading down to my car.
· Yay! I have a trash can at work!
· Blue cheese and bacon salad made by Danielle with fresh dressing and extremely high quality bacon.
· Racking the Area 51 American IPA to a corney keg for carbonation.
· The non-dairy creamer at work has one of the worst possible fonts.
· Arek eating a sandwich at Al’s Famous Deli on Woodward.
· Horny Goat Brewing Company Variety Pack.

Leave a Comment